Dev Global Jobs
Business

Paint Controller

Emirates EngineeringEK Engineering Building, Dubai, United Arab EmiratesFull-timeSalary not listed · Typical pay in United Arab EmiratesPosted Nov 19, 2026Closes Nov 30, 2026

This listing is for a Paint Controller role at Emirates Engineering, in EK Engineering Building, Dubai, United Arab Emirates. The listing describes it as a full-time position.

Written by Dev Global Jobs

DGJ summary of this job

Our own short read of this listing, built only from the facts it gives. The employer’s original text follows further down.

This listing is for a Paint Controller role at Emirates Engineering, in EK Engineering Building, Dubai, United Arab Emirates. The listing describes it as a full-time position.

From the advert, the main requirements are 3+ years of experience.

The employer does not state a salary in this listing; DGJ Insight below shows an official pay benchmark for the place where one exists.

Visa sponsorship is not mentioned. Applicants from outside United Arab Emirates should check the official work permit route before applying.

Dev Global Jobs found this job on EmiratesGroupCareers on Nov 19, 2026; applications close on Nov 30, 2026.

Employer
Emirates Engineering
Location
EK Engineering Building, Dubai, United Arab Emirates
Job type
Full-time
Pay
Not stated by the employer
Experience asked
3+ years
Found
Nov 19, 2026 on EmiratesGroupCareers
Closes
Nov 30, 2026
Employer text
934 words, about 4 min to read
Before you apply
  • Apply only on the official page (external.emiratesgroupcareers.com). Dev Global Jobs is not the employer and never asks for a fee.
  • Compare your own experience with the 3+ years the advert asks for, and show it clearly near the top of your CV.
  • Plan to apply before Nov 30, 2026.
  • Read the employer’s full text below (about 4 min) before you apply.
  • Build or check your CV with the free DGJ CV Builder.
Only on Dev Global Jobs

DGJ Insight

Our own data about this role and place, from official statistics and our live job index.

Updated Nov 19, 2026
Cost of living · United Arab Emirates
88.8 vs New York = 100

UN living-cost index for United Arab Emirates (ICSC post adjustment 55.9), as of 1 Nov 2026.

Source: ICSC post adjustment classifications (icsc.un.org)

Work permit route
  • Standard work permit and residence visa: Employer (sponsor) applies through MoHRE and ICP
  • Green Visa: Self-sponsored residence for skilled employees, freelancers and investors
  • Golden Visa: Long-term residence for talents, investors and specialists

Official routes: Federal Authority for Identity, Citizenship, Customs and Port Security

Job description

About the role

Full text from the employer, as published on EmiratesGroupCareers, arranged into sections. Nothing added or removed.

Job Purpose

At the Aircraft Appearance Centre, we elevate the aircraft's look with expert livery, precision paintwork, and impeccable interior finishes. Our advanced paint facility boasts a fully automated, climate-controlled hangar that accommodates aircraft up to the Airbus A380. From stunning exterior designs to flawless interior detailing, our skilled team ensures your aircraft stands out with exceptional quality and precision. Our paint workshops work to the highest standards of repair and application of surface finishing materials to ensure component conformity and aesthetic ambience. They manufacture decals to ensure airworthiness and customer comfort.

As Paint Controller you are responsible for the direct supervision of staff for the total restoration of the exterior finish of the aircraft by, masking, de-painting and reapplying the finishing/polishing on the aircraft. Responsible for the inspections of the tasks to make sure they comply to the standard of corporate image regarding aircraft exterior appearance in accordance with engineering work sheets, paint manufacturer's data sheets and application of company livery from the engineering drawings.

In this role you will:

  • Responsible for the correct surface preparation of masking, abrading, cleaning, stripping plus pre-treatment of the surfaces of aircraft and the application of paint coatings to the correct procedures so as to achieve a one time application system to reduce rework. This is to be carried out in accordance with the SRM (Structure Repair Manual), AMM (Aircraft Maintenance Manual) and paint manufactures data sheets and to adhere to the correct mixing, induction timing, viscosity and flash off between coats.
  • Positioning and application of the Airline's livery and lines as per two dimensional engineering drawings and the artist impressions and be able to reproduce it on the aircraft in a three dimensional manner so that it is optically and aesthetically correct. Application of markings in the correct location and colour to the airline's standard and in accordance with aircraft manufacturer's AMM (Aircraft Maintenance Manual), CMM (Component Maintenance Manual) and mandatory marks of the GCAA.
  • Must be fully capable of the corrosion control in Class 1 standard and the treatment and prevention thereof to the exterior of the aircraft structures. Identify other corrosion which may be observed during the stripping/abrading which requires additional assessment into the category of Class 1, 2 & 3. Bring it to the attention of the Senior Engineer Paint Hall and Aircraft Engineer in order for them to taken the appropriate action.
  • Responsible for the supervision of Paint Technicians working on A&C Checks where foundation paint work is needed, as well as providing advice on the correct rectification procedure. The correct installation of Commercial Campaigns Decals as required by the airline, ensuring the correct work assessment is available.
  • Before the application of coating an inspection of the aerodynamic sealant is to be carried out after application. Instruct and manage the reworking of sealants for any defects so as to achieve its aerodynamic purpose and for it not to distract from the aesthetic appearance.
  • Exercise health and safety procedures pertaining to the tasks carried out and ensuring that all staff are using the correct safety equipment, liaising with the Senior Eng paint hangar to ensure that all docking and equipment are safe before the commencing of the tasks.
  • Adjusting equipment and tools used in the restoration of aircraft finishing and materials, and the usage thereof to achieve an excellent overall finish. Ensuring the maintenance of tools and equipment in the relevant work place is carried out regularly and report any discrepancies to the Senior Eng Paint hangar for immediate action.
  • Operate electrostatic spray equipment to the required standard and be especially diligent with its safety aspects i.e. grounding of equipment, handling the guns so as to not accidently inject the product into the body due to the high pressure of the equipment. Be aware of the products which are not compatible with equipment, and optimize the use of these guns to produce an excellent overall appearance from experience.
  • Complete company documentation as required to verify that procedures have been carried out in accordance with airworthiness standards.
  • Must liaise and communicate at various levels with other areas over technical issues, in order that all the relevant parties are aware of the aircrafts status plus involvement in the pre task inspection high lighting the discrepancies which involves other trades so that the Senior Engineer Paint Hall who can then raise the necessary documents and inform the other trades of the required actions.
Qualification

To be considered for this role, you should meet the below criteria:

  • Experience in Engineering for 10+ years
  • Higher / National Diploma (12+2 or equivalent) or Apprenticeship in Engineering, Automotive or a related industry or equivalent training with a reputable airline, approved maintenance organisation.
  • Experience in post training.
  • Must have a minimum of 3 years aircraft refinishing experience.
  • Must have managed a team of junior painters/abraders and carried out the on the job (OJT) required in the correct masking, abrading and painting procedures.
  • Knowledge of safety, human factors, and general aircraft engineering practices pertaining to aircraft painting.
  • Knowledge of aircraft manuals and engineering drawings pertaining to the rework of paint finishes and correct application of markings.
  • Knowledge of different coating systems and the application there of.
Salary & benefits

Join us in Dubai and enjoy an attractive tax-free salary and travel benefits that are exclusive to our industry, including discounts on flights and hotels stays around the world. You can find out more information about our employee benefits in the Working Here section of our website www.emirates.com/careers. Further information on what’s it like to live and work in our cosmopolitan home city, can be found in the Dubai Lifestyle section.

CSI

Ask CSI about this job

Answers link to jobs and tools on Dev Global Jobs.

Get jobs like this

The best new matches, once a week. Free, one click to stop.

Community

Review Dev Global Jobs

Used this site to find a job? Tell other job seekers what worked and what did not.

Write a review on TrustpilotIt takes about two minutes↗